VHS-K10-72/230 - Chống sét 10 đôi dây tổng đài

Nguồn gốc xuất xứ: Úc
Giá:
Đơn vị: Cái
Khối lượng:
Mã sản phẩm: VHS-K10-230
Thương hiệu: LPI
Số lượng tối thiểu cung cấp: 1  Cái
Số lượng có thể cung cấp: 10  Cái/ngày
Thời gian cung cấp: 1- 3 ngày
Bảo hành: 2 năm
Mô tả hoặc các tên gọi khác: chống sét tổng đài VHS-K10-230, chống sét phiến krone, phiến krone chống sét LSA, chống sét Krone LSA, phiến krone chống sét tổng đài VHS-K10-230, chống sét 10 đôi dây tổng đài, chống sét 10 đôi dây data, chống sét 10 đôi dây điện thoại, chống sét 10 đôi dây trung kế, chống sét 10 đôi dây tín hiệu, chống sét đường ADSL

 

Chống sét trên đường điện thoại và đường dữ liệu

● Chống sét trên đường điện thoại và đường dữ liệu

● Chống sét trên đường điện thoại

● Dòng tải 150mA, 20kA 8/20μs

 

Product Description

The VHS-K10-230 is a multistage protection module designed for the protection of digital telephone and data circuits against transient over-voltages caused by lightning, induced impulses and other voltage surges. Traditional shunt-connected gas filled arresters by themselves can no longer provide adequate or required protection for sensitive line cards or newer generation digital switching systems.

The VHS-K10-230 contains ten line protection circuits on a single PCB. Each circuit consists of a primary three terminal gas filled arrester followed by a secondary transient clamping circuit.

The gas arrester provides common mode protection by bypassing transient currents to ground. The arrester chosen by LPI has a fast impulse response compatible with the requirements of advanced high-speed data networks.

The secondary transient clamping circuit comprises a series resistor in each leg plus shunt connected silicon transient protection devices. The effect of this series impedance is to provide decoupling between the primary and secondary protection elements during fast rise time impulses associated with lightning type transient events.

The effect is that fast rise time events, with high dV/dt, are diverted to the primary gas filled arrester rather than passed through to the equipment.

Following the series impedance, silicon transient protection devices provide transverse mode fine protection.

The VHS-K10-230 is earthed through two spring clips which connect to the KRONE LSA* frame. These robust tabs provide excellent electrical contact with the frame.

Application

The LPI VHS-K10-230 is designed for installation into the Krone LSA-Plus Series 2* termination system. The LPI VHS-K10-230 must be installed into disconnect blocks to allow the series impedance elements to be inserted in circuit.

Applications include the protection of telephone, data networks used for process control and automation. The LPI VHS-K10-230 can be used to protect at the MDF, Public Exchange (PSTN), PBX, Key Telephone Systems (KTS), Pay phone, as well as data distribution systems, remote instrumentation, radio transmitters etc. Suitable for primary and basic rate ISDN, Broad band ADSL, E1/T1 and PCM applications.

 

LPI VHS-K10-230

Thông số kỹ thuật LPI VHS-K10-230

Technical Data

 

Configuration:

10 pair plug in module

Protection Stages:

Gas arrester / series impedance / Silicon Protection

Max. bit rate &

Bandwidth:

8 Mbits/s & 12 MHz

 

DC Breakdown:

190-276V line to earth

190 – 262V line to line

Max working voltage:

190V line to earth

190V line to line

Surge rating:

a+b-e 20kA for 8/20μs pulse

a-b or a-e 10kA for 8/20μs pulse

Typical Let-through

Voltage:

240V @ 5kV 10/700 μs

Max Line Current: 150mA @ 25°

AC discharge current:

a+b-e 10A @ 50Hz for 1second

Return loss:

>44dB @ 3.4kHz 600Ω

>32dB @ 1MHz 120Ω

>32dB @ 3MHz 120Ω

>25dB @ 12MHz 120Ω

Capacitance

a-e, b-e < 5pF

a-b < 30pF

Loop resistance:

6.6 Ohms nominal

 

Insertion loss:

<0.05dB @ 600Ω, 3.4kHz

<0.25dB @ 120Ω, 1MHz

<0.26dB @ 120Ω, 3Mz

<0.3dB @ 120Ω, 12MHz

Insulation Resistance:

> 5MΩ @ 190 Vdc

Dimensions

119mm long x 20mm high

45mm from front of KRONE* Series 2 block when plugged in

Weight

80 g

Connection:

PCB plug in, to Krone LSA* disconnect block

Earthing:

Via spring clips to KRONE* frame

Temperature range

0 - 45°C, 10 – 90% RH

Location

BD, CD or MDF in Krone LSA* disconnect block